My '62 project
Moderators: Dan Szwarc, jleonard
Re: My '62 project
Here's a shot of the rear of the 4L60E tranny and the driveshaft bracket. We're going to have to use a 2-piece driveshaft because of the angle from the rear of the trans to the third member.
And the exhaust has been very trying. There is almost zero clearance on the left side of the block for exhaust. The right side is no problem, but the left side is really tight. So we had to do some innovative engineering for the left side exhaust.
In the picture above you can see the adapter plate that allows the GM transmission to attach to the HEMI block.
And the exhaust has been very trying. There is almost zero clearance on the left side of the block for exhaust. The right side is no problem, but the left side is really tight. So we had to do some innovative engineering for the left side exhaust.
In the picture above you can see the adapter plate that allows the GM transmission to attach to the HEMI block.
1962 Continental resto-mod
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
- darrylqmiller
- Lincoln Maniac
- Posts: 496
- Joined: Tue Apr 05, 2011 12:58 am
- Location: Peachtree City, Georgia
- Contact:
Re: My '62 project
Those are very interesting exhaust manifolds. Don't think I've ever seen some like that. Keep up the good work.
How I bagged it: http://www.thelincolnforum.net/phpbb3/v ... 42&t=42724
Build thread: http://www.thelincolnforum.net/phpbb3/v ... 38&t=38977
What I thought was fuel pump noise: http://www.thelincolnforum.net/phpbb3/v ... =1&t=39580
Edelbrock 1406 install: http://www.thelincolnforum.net/phpbb3/v ... =1&t=45554
Build thread: http://www.thelincolnforum.net/phpbb3/v ... 38&t=38977
What I thought was fuel pump noise: http://www.thelincolnforum.net/phpbb3/v ... =1&t=39580
Edelbrock 1406 install: http://www.thelincolnforum.net/phpbb3/v ... =1&t=45554
- ReijerLincoln
- Lincoln-ally Insane
- Posts: 4939
- Joined: Thu Jan 06, 2005 7:15 am
- Location: The Netherlands
- Contact:
- 66Lincoupe
- Lincoln-ally Insane
- Posts: 3720
- Joined: Mon Nov 17, 2008 1:20 pm
- Location: Surprise, AZ
- Contact:
Re: My '62 project
A couple more pics.
Getting ready for paint...
Here you can see where the frame rail was modified to accept the Hemi...
Getting ready for paint...
Here you can see where the frame rail was modified to accept the Hemi...
1962 Continental resto-mod
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Re: My '62 project
I've spent months looking for wheels, and really didn't find any that really grabbed me. I didn't want to go too modern and didn't want to go too retro (Cragars or similar 5-stars). I came close to going with steelies, but wasn't happy about the weight. I finally settled on these. They're Centerlines in 20". The wheels are rotary forged T-6061 billet aluminum, so they're both light (26 pounds) and strong (2200 pound rating). The hi-polish might be a bit of a bitch to keep up, but not that bad.
1962 Continental resto-mod
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
- sauceman
- Addicted to Lincolns
- Posts: 1382
- Joined: Thu Sep 17, 2009 5:33 pm
- Location: Napanee, Ontario, Canada
- Contact:
Re: My '62 project
Nice wheels,
You forgot to answer my question about the wiring harness for the HEMI. How does it tie into the factory harness? Do you have to run any of the modern dash for the MEL?
cheers
You forgot to answer my question about the wiring harness for the HEMI. How does it tie into the factory harness? Do you have to run any of the modern dash for the MEL?
cheers
Good judgement comes from experience, and often experience comes from bad judgement.
Yugoslavia '94' , Israel/Syria '99 , Bosnia '02 , Afghanistan '08-'09
My 1977 Town Car build
Yugoslavia '94' , Israel/Syria '99 , Bosnia '02 , Afghanistan '08-'09
My 1977 Town Car build
Re: My '62 project
I'm not sure how the Hemi wiring is integrated with the factory wiring. That's way above my head. We're also converting all the instruments to modern internals and installing aftermarket a/c, converting all the windows to electric, adding cruise control, etc. Lots of wiring fun.
1962 Continental resto-mod
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Re: My '62 project
I am trying to make a Engine conversion to my 67' , Im trying to find all the ideas i can.
Was this swap for the hemi a very complex install? many modifications? Where else can I find more Engine swaps or ideas.
I apologize, I am new to this Forum
Was this swap for the hemi a very complex install? many modifications? Where else can I find more Engine swaps or ideas.
I apologize, I am new to this Forum
-
- Newbie
- Posts: 14
- Joined: Wed Apr 09, 2014 11:49 pm
- Location: San Diego CA
- Contact:
Re: My '62 project
Very nice project you have going on, I want to to do conversion my self with my 61 to a all newer drive train so im defiantly subscribing to this thread
Have you looked at http://detroitsteelwheel.com/ they have steel wheel in 18 and 20 inch ,very classic look they even have white walls for 20" .
congrats again ion such a nice project
Have you looked at http://detroitsteelwheel.com/ they have steel wheel in 18 and 20 inch ,very classic look they even have white walls for 20" .
congrats again ion such a nice project
- twistngo
- Frequent Contributor
- Posts: 243
- Joined: Tue May 18, 2010 12:18 am
- Location: Louisville, KY
- Contact:
Re: My '62 project
You are under the right index for motor swaps, there is mine 1966 LCC resto mod conversion, or 63 convertible 4.6 build, and the craziest continental project ever. These should keep you busy for a bit there are some 460 swaps also just don't know the builds right off. Search under 460 maybe.
JonW looks good. I am going the two piece drive shaft rout for the same reason. Was going to dump my 8.8 for a 9 inch , but after buying lots of 9 inch stuff found that the 9 inch pinion is only .75 inch lower than the 8.8. Since the 9 inch would have to go and be narrowed to match the 8.8 didn't seem worth it. So it's Ebay time for the 9 inch stuff. Would like to see some more pics of your drive shaft set up, making mine frim a 94 F150 two piece unit.
JonW looks good. I am going the two piece drive shaft rout for the same reason. Was going to dump my 8.8 for a 9 inch , but after buying lots of 9 inch stuff found that the 9 inch pinion is only .75 inch lower than the 8.8. Since the 9 inch would have to go and be narrowed to match the 8.8 didn't seem worth it. So it's Ebay time for the 9 inch stuff. Would like to see some more pics of your drive shaft set up, making mine frim a 94 F150 two piece unit.
66 Continental convertible, 13 SHO slightly tuned
02 Custom built softtail, 15 Expedition EL, 05 Thunderbird
00 Crown Vic Eaton M112 blower, Tremec 5speed......etc
Suzuki RF900 Just a little engine work...... And yes my wife is invisible
02 Custom built softtail, 15 Expedition EL, 05 Thunderbird
00 Crown Vic Eaton M112 blower, Tremec 5speed......etc
Suzuki RF900 Just a little engine work...... And yes my wife is invisible
Re: My '62 project
It's been painted, the drivetrain is installed and it's almost ready to fire. This shop has done an outstanding job in every respect. Their workmanship has been first class, and the engine bay is very tidy and uncluttered. We trying to get it ready for Cruisin' the Coast in October, it's going to be close.
1962 Continental resto-mod
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
Yeah, it's got a Hemi
1979 Mark V 1 of 1
Triple Turquoise
1979 Mark V Bill Blass Edition
- Suicidekid63
- Lincoln-ally Insane
- Posts: 3167
- Joined: Tue Jan 13, 2009 3:21 pm
- Location: Rt.66 in the beautiful Ozark Mountains of Missouri
- Contact:
Re: My '62 project
Awesome, Jon! Glad to hear and clearly see that Carl & crew have came through on this job.
Post when it's yours to drive. I'd love to check it out in person, man.
Post when it's yours to drive. I'd love to check it out in person, man.
Steven Wecker 1963 Lincoln Continental sedan survivor/ Ermine white w/ Pearl honey beige interior
"Moby"- The Wixom whale / aka: "Pale Rider"
ALWAYS carry a fire extinguisher!!!
"Moby"- The Wixom whale / aka: "Pale Rider"
ALWAYS carry a fire extinguisher!!!
- suburban_gorilla
- Dedicated Enthusiast
- Posts: 527
- Joined: Wed Sep 10, 2008 2:15 pm
- Contact:
Re: My '62 project
Holy shit that looks insane! very nice. Thanks for keeping us updated.
Omar
Toronto, Canada.
1962 Lincoln Continental, 2019 Jaguar I-PACE, 2017 BMW X5
2008 Maserati Quattroporte Sport GTS [sold], 2008 Honda Pilot [sold], 1987 Cadillac Brougham D'elegance [sold], 2007 Acura CSX [gone]
Toronto, Canada.
1962 Lincoln Continental, 2019 Jaguar I-PACE, 2017 BMW X5
2008 Maserati Quattroporte Sport GTS [sold], 2008 Honda Pilot [sold], 1987 Cadillac Brougham D'elegance [sold], 2007 Acura CSX [gone]
- Suicidekid63
- Lincoln-ally Insane
- Posts: 3167
- Joined: Tue Jan 13, 2009 3:21 pm
- Location: Rt.66 in the beautiful Ozark Mountains of Missouri
- Contact:
Re: My '62 project
Jon,
Went out to Carl's on my lunch hour, today. The '62 looks awesome! So much work has went into this resto. It looks great, man! Kudos!!!
Went out to Carl's on my lunch hour, today. The '62 looks awesome! So much work has went into this resto. It looks great, man! Kudos!!!
Steven Wecker 1963 Lincoln Continental sedan survivor/ Ermine white w/ Pearl honey beige interior
"Moby"- The Wixom whale / aka: "Pale Rider"
ALWAYS carry a fire extinguisher!!!
"Moby"- The Wixom whale / aka: "Pale Rider"
ALWAYS carry a fire extinguisher!!!
Who is online
Users browsing this forum: No registered users and 1 guest